Introducing Envolash Glue Support – a 2 in 1 product dedigned as a primer to prime the natural lash surface, ensuring optimal adhesion between the natural lash and the extension. It also can be used as an accelerator to help the adhesive cure faster.

To use as a Primer

Our Lash primer is designed to prepare the surface of the natural lash by providing optimal conditions for glue adhesion between the extension and natural lash, without over-drying or stripping the natural lash of oils. It provides the optimum pH required for the glue to grab without much effort. Primer is ideal for clients with oily skin where glue may not be grabbing the lash.

How to Use as a Primer:

1. Cleanse lashes and thoroughly rinse and dry
2. Apply a small amount of primer onto 2 clean micro brushes-do not oversaturate
3. Apply to all areas where the lash will be bonded, careful not to touch the skin
4. Allow drying for 2 minutes before application.
5. Proceed as normal with lash application

 

To use as an Accelerator

Recommended for advanced lash artists only.

In less than ideal humidity conditions, the adhesive may cure slower due to the lack of moisture. Applying a small amount of Glue Support to the base of the strip will speed up the curing time of the adhesive.

How to use as an Accelerator:

6. Wet a micro brush with a small amount of booster
7. Remove as much booster off the brush onto a clean towel
8. Rub the working section (small) of the lash tray. The booster should barely be visible
9. Allow to dry
10. Proceed to make fans and dip in glue

Note: glue will require changing more often due to the presence of Glue Support.

 

MSDS

MSDS |MATERIAL SAFETY DATA SHEET

Section 1 – Chemical Product and Company Identification

MSDS NAME COMPANY NAME	Glue Support 2 In 1 ENVOLASH PTY LTD
COMPANY ADDRESS	15 Peerless Court                              Avondale Heights                             Victoria 3034 Australia 0415 217 186

 

 

Section 2 – Composition and Ingredient Information                          

 

 

Ingredient Component Name

Ethanol

CAS Number 64-17-5

Concentration 30%

Glycerin CAS 56-81-5

Concentration 10%

Carbomer

CAS Number 9007-20-9

Concentration 0.5%

Water

CAS Number 7732-18-5

Concentration 85%

Triethanolamine

CAS Number 102-71-6

Concentration 2.5%

Fragrance

CAS Number 35206-51-0

Concentration 1%

Section 3 – Hazards Identificatio

 

Hazard Risk Classification	Category 1
Flammability	2
Physical Hazard	1
Potential Health Effect	Eye: Irritating to eyes. Causes excessive tearing. Eyelids may bond   Skin: May cause skin irritation Inhalation: May cause respiratory tract irritation. The toxicological properties of this substance have not been fully investigated   Ingestion: Not expected to be harmful by ingestion. Rapidly polymerizes (solidifies and bonds in mouth. It is almost impossible to swallow.
WARNING : MAY CAUSE EYE AND RESPIRATORY IRRITATION BONDS SKIN IN SECONDS.   Relevant routes of exposure: Inhalation, Eyes Potential Health Effects Inhalation : Exposure to vapors above the established exposure limit result in respiratory irritation which may lead to difficulty in breathing and tightness in the chest

 

Section 4 – First Aid Measures                                                                    

 

 

Inhalation	Remove to open space with fresh air. Seek medical attention to treat symptomatically if discomfort persist. Keep eye covered until deboning is complete, usually within 1-3 days. Medical attention should be sought in case the liquid trapped behind eyelid caused abrasive damage.
Eye Contact	Non provided
Skin Contact	In case of unexpected irritation, immediately wash skin with soap and large amounts of water
Ingestion	Ingestion is not likely. See supplemental page for emergency procedures.

 

 

 

 

Section 5 – Fire Fighting Measures                                                           

 

 

Flash Point	29℃ (85 deg F) Tagliabue closed cup
Auto Ignition temperature	485℃
Flammable/Explosive Limits-lower%	Not determined
Flammable/Explosive Limits-upper%	Not determined
Hazardous Decomposition Materials	N/A
Suitable Extinguishing Media	Dry powder. Foam and Water spray. Carbon dioxides.
Protective Equipment	Fire fighters should wear positive pressure self- contained breathing
Hazardous combustion products	Trace amount of toxic and or irritating fumes may be released, and the use of breathing apparatus is recommended.
Unusual fire or explosion hazard	None
Specific Hazard(s)	Trace amount of toxic and or irritating fumes may be released, and the use of breathing apparatus is recommended.

 

Section 6 – Accidental Release Measures                                                 

 

 

General Information	None provided
Environmental precautions	Ventilate Area
Disposal and Clean Up	Do not use cloths for mopping up. Flood with water to complete polymerization and scrape off the floor. Cured material can be disposed of as non- hazardous waste

 

 

Section 7 – Handling and Storage                                                             

 

 

Handling Precautions	Avoid contact with eyes. Avoid breathing of vapors
Storage	Keep in a cool, well ventilated area away from heat

 

 

Section 8 – Exposure Controls and Personal Protection                     

 

Engineering Controls	Use positive down-draft exhaust ventilation if general ventilation is insufficient to maintain vapor concentration below established exposure limits. Respiratory
Respiratory Protection	Use NIOSH approved respirator if there is potential to exceed exposure limits. Observe OSHA regulations for respiratory use (29 CFR 1910.134)
Skin Protection	N/A
Eye/Face protection	Chemical splash goggles or safety glasses with side shields.
General Hygiene measures	N/A

 

Section 9 – Physical and Chemical Properties                                       

 

 

Physical State	Transparent liquid
Odour	Aromatic
pH	N/A
Specific Gravity	1.04 @ 75oF
Boiling Point	78.2OC
Flash Point	Not available
Flammability	Not available
Evaporation Rate (Ether=1)	N/A
Ignition Temperature	Not available
Melting/Freezing Point	Not available
Solubility	Polymerized by water
Vapour Density	Approximately 3
Vapour Pressure	Less than 0.2mm
Volatile Organic Compound (EPA Method24)	87..9%

 

 

 

Section 10 – Stability and Reactivity                                                        

 

 

Stability	Stable under recommended storage conditions
Conditions to Avoid	Spontaneous polymerization
Incompatible Materials	None listed
Hazardous Polymerization	Rapid exothermic polymerization will occur in the presence of water, amines, and alcohols
Hazardous decomposition	None listed

 

Product toxicity da Hazardous component ta : Acute oral LD50〉50 NTP Carcinogen 00mg/kg(rat) Acut IARC Carcinogen e dermal LD50 OSHA Ethyl Cyanoacrylate 7058-85-0 NO NO NO Carbon Black 1333-86-4 NO Group 2B Yes

Section 11– Toxicological Information

〉2000mg/kg(rabbit)

Section 12– Ecological Information

Not known

Section 13– Disposal Consideration

No data available

Section 14– Transport

INTERNATIONAL AIR TRANSPORT ASSOCIATION (IATA) :

This product is not classified as dangerous goods, by rules of IATA. U.S Department of Transportation (DOT) Shipping regulations:

This product is not classified as dangerous goods, per U.S. DOT regulation under 49CFR 172.101. Proper shipping name : Volume X

Hazard Class number and description : Not applicable. UN identification number : Not applicable. Packing group : Not applicable.

Section 15– Other Information                                                                   

DISCLAIMER :

All the information of Material Safety Data Sheet is provided on the basis in good faith and is believed to be trustworthy but is for reference only.

The users are responsible for selecting the suitability of the products and methods of use.

Our company assumes no responsibility for use or reliance upon this information.  The users are responsible for selecting the suitability of the products and methods of use.